Blown-In Attic Insulation In Bradford, Ontario
Blown-in attic insulation spreads one unbroken layer across the attic floor, eave to eave, and reaches R-60 at the right depth. It suits empty attics, patchy batts and any floor with open joist bays.
Every blown-in attic insulation job begins with a free depth reading, and the price is set in writing before a date is booked. Every attic job carries full insurance, and most of these jobs are done in one day.
Blown-In Attic Insulation details
Blown-In Attic Insulation Fills Gaps That Batts Leave Behind
Batts come in fixed widths, so every place they cannot reach stays empty. Cross bracing, wire runs and joists set at odd spacing leave strips of bare drywall that leak heat all winter long.
Blown-in attic insulation pours around those obstacles instead. The fibres pack into corners and settle against wires, so the whole ceiling ends up with the same cover. That even coverage is the reason blown-in material is our choice for nearly every attic floor.
Fibreglass Or Cellulose For Blown-In Attic Insulation
Either one makes good blown-in attic insulation. Loose fibreglass is light, shrugs off moisture and keeps its height well over time. Cellulose is ground from recycled newsprint, packs a little denser, and costs about the same per square foot.
The attic decides which one we use. A shallow roof with a tight eave often works better with fibreglass, while an attic full of small gaps around truss webs can suit cellulose. Your quote names the product and the depth it will reach.
How Deep Blown-In Attic Insulation Has To Go For R‑60
R-60 works out to somewhere between 17 and 22 inches of blown-in attic insulation, and the exact figure varies by product. Rulers are fixed to the trusses at several points before the hose comes up, so the target line is plain to see.
When the floor is finished, the depth is read again at those rulers, and the R-value it reached is printed on the invoice. That number is worth keeping if the house is ever listed for sale.
Prep Work Before Blown-In Attic Insulation Goes In
Sealing comes first, since loose fill does nothing to stop air leaking through the ceiling. Baffles get stapled into each eave bay so the soffits stay open, and the hatch gets a gasket. Where the house already has a decent layer, our attic insulation top-up page explains how fresh material is laid over the top.
Book A Free Blown-In Attic Insulation Reading
Call (289) 210-8362 or use the request box below, and we will read the depth in your attic and price the job. Blown-in attic insulation for a bare Bradford attic usually costs $1.80 to $3.00 per square foot. For every other service, head back to the Bradford attic insulation home page.
Pair This With Another Attic Job
A typical Bradford attic combines a couple of these on one visit.
-
Attic Insulation Top-Up
With an attic insulation top-up, fresh fill is blown on top of the layer you already have until a thin or sunken attic floor reaches R-60. Dry, clean material underneath is left right where it lies.
-
New Home Attic Insulation Upgrade
A new home attic insulation upgrade takes the minimum layer a builder left and builds it up to R-60, fixing the eaves, the hatch and the ceiling holes as it goes. For most newer Bradford houses it is the first upgrade worth doing.
-
Attic Air Sealing
Attic air sealing shuts the holes in your ceiling where heated air slips into the attic, from recessed lights and fan boxes to the hatch. It is step one on every insulation job we take.
-
Attic Ventilation
Good attic ventilation draws cold, dry air through the soffits and releases it up near the ridge, which keeps the roof deck dry through the winter. We look at attic ventilation in every attic, because new insulation must never block it.
-
Attic Insulation Removal
Attic insulation removal vacuums out damp, mouldy, flattened or rodent-fouled insulation, leaving a bare floor ready for sealing and fresh insulation. Attic insulation removal is the right first step when the old layer can no longer do its job.
-
Attic Insulation Rebate
Ontario's attic insulation rebate covers part of the cost of raising an attic to R-50 under Home Renovation Savings, a program Enbridge Gas runs jointly with Save on Energy. Below is what it pays, who can apply and how contractors fit in, last checked October 2026.
-
Attic Insulation Cost
Attic insulation cost in Bradford mostly falls between $1.20 and $3.00 per square foot, which is about $1,200 to $3,000 for an average subdivision attic. Your exact figure arrives on paper once a free depth reading is done.
Get Your Attic Measured At No Charge
A single visit gives you the depth, the holes to seal and the price, and the reading itself is free.
Ask For Your Free Depth Reading
Give us the basics on your home, and our office will phone back to pick a visit date. Calls go to +1 (289) 210-8362.